Description

Home Electronic Component Chips Sensor Arduino Module Raspberry Pi DC6.5-50V 380W BLDC 3 Phase DC Brushless Motor Driver Board Motor Controller Popular Popular Product Introduction Product features: This drive is a DC three-phase brushless and Hall free control board The motor can operate normally without Hall BLDC wide voltage 6.5-50V high-power 380W DC three-phase high-speed brushless and non-inductive controller Added PWM signal input, supporting 3.3V system PLC 0-5V analog quantity, signal input control Dual Capacitor Version : Special instructions for external signal input: 1. The connection of V/P short contacts is the effective identification of PWM signal input. The true PMW signal supports a 3.3V system, and PMW signals need to be input from two ports (PWM GND) of the wiring terminals. 2. When the V/P short contact is disconnected, the 0-5V analog signal input is valid (default disconnection at the factory). During analog input, the built-in potentiometer on the board can be used for voltage regulation. If you want to connect the 0-5V analog signal input externally, you must unplug the jumper cap on the board and cut off the potentiometer voltage signal. Then, input the 0-5V analog signal from the two ports (0-5 GND) of the wiring terminal, and the maximum voltage should not exceed 5V 3. The forward and reverse directions and brakes are grounded through a switch, which is effective for low levels. External MCU can also provide low level signals. The front row of wiring terminals are all weak current signals that are directly input to the MCU main control, and cannot touch or touch high voltage and strong current. Interface Description: 1. U V W 3-phase line output connected to brushless motor 2. 5V GND motherboard comes with 5V (current not exceeding 200MA) 3. VCC GND main power supply (external DC power supply) 4. SC speed pulse signal output (only interface reserved without technical support) 5. DIR forward and reverse control remains effective at low levels (can be connected to external switches to ground) 6. BRAKE brake control remains effective at low level (can be switched externally to ground) 6.0-5V PWM speed control signal dual input terminal (the built-in potentiometer on the board can also be used for speed control through jumper switching, and external 0-5V analog PWM duty cycle signal input speed control) Full SMD process, stable performance, user-friendly design interface, all equipped with wiring terminals, standard heat dissipation fins, on-board speed regulation potentiometer, which can be used when powered on by hand, saving time and worry Main board specifications and parameters: Product name: zs-x11f-2 Working voltage: 6.5-50V Drive current: rated 16A with air cooling and heat dissipation of 30A Maximum power: 380W Overcurrent protection: Yes Locked rotor protection: Yes (after locked rotor, the current automatically drops and runs in isolation) Over temperature protection: Yes (over temperature power reduced by half) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor). Product size: 63MM long * 45MM wide * 31MM high Weight: around 76g Precautions: 1. Reverse connection of the positive and negative poles of the power supply on the motherboard can cause permanent damage to some chips on the board (even if it lasts for one second) 2. During normal operation, the motor output terminal has sampling overcurrent protection. Due to the high power and current of the module, please do not artificially short circuit the module when it is not working properly. However, there is a possibility of burning the circuit and exploding the tube. For the first wiring test, please use a low current and low voltage test. After it is OK, apply high current and high voltage again. As it is a bare board module, pay attention to the insulation of the wiring head and avoid strong voltage touching the parts on the board 3. Do not connect motors that do not match or differ significantly from the voltage, current, and power of the drive module Single Capacitor Version Product Introduction: This drive is a DC three-phase brushless Hall free control board, and the motor can operate normally without Hall. The ultimate upgrade BLDC wide voltage 6.5-50V high-power 380W DC three-phase high-speed brushless and inductive controller, with added PWM signal input, supporting 3.3V PLC 0-5V analog signal control. Product parameters: Product Name: 380W Brushless Hall Free DC Motor Controller Working voltage: 6.5-50V Drive current: rated 16A with air cooling and heat dissipation of 30A Maximum power: 380W Overcurrent protection: None (requires external fuse) Locked rotor protection: Yes (current automatically decreases after locked rotor) Over temperature protection: Yes (power reduced by half when the temperature exceeds 100 degrees) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Interface Description: 1. U V W phase line output connected to motor 2. 5V GND motherboard comes with power supply (current not exceeding 300MA) 3. VCC GND motor main power supply (external DC power supply) 4. SC speed pulse signal output 5. DIR forward and reverse control (external switch with lead wire) 6. BRAKE brake control (can be wired to an external switch) 7. 0-5V PWM speed control signal input (the built-in potentiometer on the board can also be used for speed control through jumper switching. The 0-5V analog PWM duty cycle signal input is used for speed control) Product List: 1X drive board Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address ,Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. Refund All package need to wait 30 days (US only n eed 7-10 days) , Please take care it.Less than 30 days,we can't take a refund . If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item. Home Electronic Component Chips Sensor Arduino Module Raspberry Pi DC6.5-50V 380W BLDC 3 Phase DC Brushless Motor Driver Board Motor Controller Product Introduction Product features: This drive is a DC three-phase brushless and Hall free control board The motor can operate normally without Hall BLDC wide voltage 6.5-50V high-power 380W DC three-phase high-speed brushless and non-inductive controller Added PWM signal input, supporting 3.3V system PLC 0-5V analog quantity, signal input control Dual Capacitor Version : Special instructions for external signal input: 1. The connection of V/P short contacts is the effective identification of PWM signal input. The true PMW signal supports a 3.3V system, and PMW signals need to be input from two ports (PWM GND) of the wiring terminals. 2. When the V/P short contact is disconnected, the 0-5V analog signal input is valid (default disconnection at the factory). During analog input, the built-in potentiometer on the board can be used for voltage regulation. If you want to connect the 0-5V analog signal input externally, you must unplug the jumper cap on the board and cut off the potentiometer voltage signal. Then, input the 0-5V analog signal from the two ports (0-5 GND) of the wiring terminal, and the maximum voltage should not exceed 5V 3. The forward and reverse directions and brakes are grounded through a switch, which is effective for low levels. External MCU can also provide low level signals. The front row of wiring terminals are all weak current signals that are directly input to the MCU main control, and cannot touch or touch high voltage and strong current. Interface Description: 1. U V W 3-phase line output connected to brushless motor 2. 5V GND motherboard comes with 5V (current not exceeding 200MA) 3. VCC GND main power supply (external DC power supply) 4. SC speed pulse signal output (only interface reserved without technical support) 5. DIR forward and reverse control remains effective at low levels (can be connected to external switches to ground) 6. BRAKE brake control remains effective at low level (can be switched externally to ground) 6.0-5V PWM speed control signal dual input terminal (the built-in potentiometer on the board can also be used for speed control through jumper switching, and external 0-5V analog PWM duty cycle signal input speed control) Full SMD process, stable performance, user-friendly design interface, all equipped with wiring terminals, standard heat dissipation fins, on-board speed regulation potentiometer, which can be used when powered on by hand, saving time and worry Main board specifications and parameters: Product Name: ZS-X11F V3 Working voltage: 5-50V (limit 60V) Driving current: rated 16A plus air cooling 25A Power: rated 200W-250W peak 300W (please leave a margin of use) Over-current protection: Yes Blocking protection: Yes (after blocking the current automatically drops to hit the run) Over-temperature protection: Yes (over-temperature power halved) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000RPM (14-pole motor). Limit can still reach 380W, must do extra cooling treatment Precautions: 1. Reverse connection of the positive and negative poles of the power supply on the motherboard can cause permanent damage to some chips on the board (even if it lasts for one second) 2. During normal operation, the motor output terminal has sampling overcurrent protection. Due to the high power and current of the module, please do not artificially short circuit the module when it is not working properly. However, there is a possibility of burning the circuit and exploding the tube. For the first wiring test, please use a low current and low voltage test. After it is OK, apply high current and high voltage again. As it is a bare board module, pay attention to the insulation of the wiring head and avoid strong voltage touching the parts on the board 3. Do not connect motors that do not match or differ significantly from the voltage, current, and power of the drive module Single Capacitor Version Product Introduction: This drive is a DC three-phase brushless Hall free control board, and the motor can operate normally without Hall. The ultimate upgrade BLDC wide voltage 6.5-50V high-power 380W DC three-phase high-speed brushless and inductive controller, with added PWM signal input, supporting 3.3V PLC 0-5V analog signal control. Product parameters: Product Name: 380W Brushless Hall Free DC Motor Controller Working voltage: 6.5-50V Drive current: rated 16A with air cooling and heat dissipation of 30A Maximum power: 380W Overcurrent protection: None (requires external fuse) Locked rotor protection: Yes (current automatically decreases after locked rotor) Over temperature protection: Yes (power reduced by half when the temperature exceeds 100 degrees) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Interface Description: 1. U V W phase line output connected to motor 2. 5V GND motherboard comes with power supply (current not exceeding 300MA) 3. VCC GND motor main power supply (external DC power supply) 4. SC speed pulse signal output 5. DIR forward and reverse control (external switch with lead wire) 6. BRAKE brake control (can be wired to an external switch) 7. 0-5V PWM speed control signal input (the built-in potentiometer on the board can also be used for speed control through jumper switching. The 0-5V analog PWM duty cycle signal input is used for speed control) Product List: 1X drive board Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address ,Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. Refund All package need to wait 30 days (US only n eed 7-10 days) , Please take care it.Less than 30 days,we can't take a refund . If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item. On Dec 6, 2023 at 08:27:59 PST, seller added the following information: